Logo
GXP2120 Executive IP Phone
Device Configuration
Software Version: 1.0.1.26

ACCOUNT 3

Account Active:
No Yes
Account Name:
(e.g., MyCompany)
SIP Server:
(e.g., sip.mycompany.com, or IP address)
Secondary SIP Server:
(e.g., sip.mycompany.com, or IP address)
Outbound Proxy:
(e.g., proxy.myprovider.com, or IP address)
SIP User ID:
the user part of an SIP address
Authenticate ID:
can be same or different from SIP UserID
Authenticate Password:
(not displayed for security protection)
Name:
 
(optional, e.g., John Doe)
 
DNS Mode:
A Record SRV NAPTR/SRV Use Configured IP
Primary IP:
Backup IP 1:
Backup IP 2:
TEL URI:
Disabled User=Phone Enabled
SIP Registration:
No Yes
Unregister On Reboot:
No Yes
Register Expiration:
(in minutes. default 1 hour, max 45 days)
local SIP port:
(default 5064)
SIP Registration Failure Retry Wait Time:
(in seconds. Between 1-3600, default is 20)
SIP T1 Timeout:
SIP T2 Interval:
SIP Transport:
UDP     TCP     TLS/TCP
Check Domain Certificates:
No Yes
Remove OBP from Route:
No Yes
Validate Incoming Messages:
No Yes
Support SIP Instance ID:
No Yes
NAT Traversal:
SUBSCRIBE for MWI:
No Yes
PUBLISH for Presence:
No Yes
Proxy-Require:
Voice Mail UserID:
(UserID for voice mail system)
Send DTMF:
  in-audio     via RTP (RFC2833)     via SIP INFO
DTMF Payload Type:
Early Dial:
No Yes (use "Yes" only if proxy supports 484 response)
Dial Plan Prefix:
(this prefix string is added to each dialed number)
Dial Plan:
BLF Call-pickup Prefix:
(this prefix is prepended when answering call with BLF key)
Delayed Call Forward Wait Time:
(Allowed range 1-120, in seconds.)
Enable Call Features:
No Yes (if yes, call features using star codes will be supported locally)
Call Log:
  Log All Calls
  Log Incoming/Outgoing only (Missed calls NOT recorded)
  Disable Call Log
Session Expiration:
(in seconds. default 180 seconds)
Min-SE
(in seconds. default and minimum 90 seconds)
Caller Request Timer:
No Yes (Request for timer when making outbound calls)
Callee Request Timer:
No Yes (When caller supports timer but did not request one)
Force Timer:
No Yes (Use timer even when remote party does not support)
UAC Specify Refresher:
UAC UAS Omit (Recommended)
UAS Specify Refresher:
UAC UAS (When UAC did not specify refresher tag)
Force INVITE:
No Yes (Always refresh with INVITE instead of UPDATE)
Enable 100rel:
No Yes
Account Ring Tone:
system ring tone
custom ring tone 1
custom ring tone 2
custom ring tone 3
Ring Timeout:
(in seconds. Between 30-3600, default is 60)
Line-seize Timeout:
(in seconds. Between 15-60, default is 15)
Send Anonymous:
No Yes   (caller ID will be blocked if set to Yes)
Anonymous Call Rejection:
No Yes
Auto Answer:
No Yes
Allow Auto Answer by Call-Info:
No Yes
Refer-To Use Target Contact:
No Yes
Transfer on Conference Hangup:
No Yes
Preferred Vocoder:
(in listed order)
choice 1:  
choice 2:  
choice 3:  
choice 4:  
choice 5:  
choice 6:  
choice 7:  
SRTP Mode:
Disabled       Enabled but not forced
Enabled and forced       Optional
Symmetric RTP:
No Yes
Silence Suppression:
No Yes
Voice Frames per TX:
(up to 10/20/32/64 for G711/G726/G723/other codecs respectively)
No Key Entry Timeout:
(in seconds, default is 4 seconds)
Use # as Dial Key:
No Yes
G723 rate:
6.3kbps encoding rate 5.3kbps encoding rate
iLBC frame size:
20ms 30ms
iLBC payload type:
(between 96 and 127, default is 97)
eventlist BLF URI:
Special Feature:
 
 
SIP User ID:
the user part of an SIP address
Authenticate ID:
can be same or different from SIP UserID
Check Domain Certificates:
When set to Yes/Enabled, we will check the domain certificate as defined in RFC5922
All Rights Reserved 2010 Grandstream Networks, Inc.